Set An Appointment

 

 

What are your opinions on Installing A Bathtub?

Setting up a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently available, the job can move immediately; if you need to open a wall surface to eliminate the old tub as well as position the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually certified yourself for the task and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is better to think about employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your shower room if you have actually already purchased a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your tools and product list should comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is detach the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this process. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Before carrying on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washing machines are in place in between the faucet as well as the sink. Protect the tap in position with the maker supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former type ought to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Mounting the Tub

Using the two wood boards under its feet, place the bath tub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little points.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub until the level checks out degree.
To set up taps, fit all-time low of the furthest versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub must wait until the tub has actually been used at the very least once as this will resolve it into its final placement.

 

 

Preparing for the Setup

To start with, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.

 

 

Tiling Around the Tub

In the location where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealer can break fairly very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you like reading about How to Install a Bathtub? Create feedback down below. We'd be delighted to know your suggestions about this piece. We are looking forward that you come back again before long. So long as you liked our blog entry plz be sure to share it. We recognize the value of reading our article about Installing A Bathtub.

Information Here